Inferno #02 01 мая 2001

Софт

Softinka - description of a new text editor ZX-WinWord V3.0.

      ZX-WinWord V3.0 Modul v1.03

(C) Shaitan / Stars of Keladan

 Presenting your attention the description
File additions to our editor
ZXWinWord v3.0 (with other versions of the editor data 
supplement does not work will). Firstly, I want to say about

that I was led to this innovation. To add kakuyunibud function 
in the editor should be have a free chunk of memory, which

today no longer exists. It's no joke
process 48Kb and 32Kb of text sprites. After long walks in the 
source code, free memory was found, but very it is not enough, 
and the editor wanted to make it accessible to everyone (not 
all yet memory in wheelbarrows more than 128Kb).

It was therefore decided to make an overlay
structure.
 To load the
you need to select the function from the main menu
click Overlay. This will be followed scans the current drive 
for a file on him Additions w.wor3_0.add. If such a file on disk

No then you will be breaking off, otherwise it will be an 
analysis, then you will be asked to choose one of the available 
overlays. After loading is directly overlay will take you to 
the main menu where you can already work as well as before. To

to run the downloaded overlay
editing mode, you must have to be in command mode (press EXTEND)
and start the overlay key V. After
then act according to the description of the overlay.


           Description overlays

In this version of the file has Additions
Xia three overlay. On each order.


    GFX Printing Text v1.0

This overlay is used for printing the document together with 
the sprites, the which have all long been dreaming of. 
Immediately after it is loaded into memory you need to also 
load the printer driver. In the author's delivery driver 
attached printer connected through the ZX-Lprint

III. You navenoe think what to write
driver is the destiny of only the elect. I
you for this answer, that the driver napisat
not easy, but very simply, is used for long-established 
standrat on driver. Thus, the driver allocated

256 bytes, located at
# 5B00-# 5BFF (23296-23551). Overlay works with the driver as 
follows. Before you print to initialize the device (makes the 
call procedures at # 5B02 [23298]). For

output bytes to the printer called the procedure located at # 
5B00 [23296]. Both of these procedures are called

every time you print the text. The main feature is that if you
otslezhivate pressing BREAK, then
necessary when it is pressed, reset
Flag C.
 And now on with the overlay. After
thereof, you will see the start menus, with
following paragraphs.
 F.page - page selection, which is to be printed.
 E.page - choose the page on which
inclusive, will be used for printing.
 Density - choose print density.
 Re-install - pereinstalyatsiya overlay.
Simply put download a new driver
printer.
 Start - run directly overlay.

 The printing process uses the following ESC-sequence.
 # 1B # 4A # 18 moving the paper forward
24 * 0.118 mm
 # 1B # 2A N misuse of print
graphical mode. N - number density
from 0 to 6.
 # 0D-back to the printer head to the starting position.


     Text Convertor v1.0

 As you probably guessed from the title, this overlay is 
designed to converting text from

memory in a format suitable for use in
editor.
 Menus of the overlay has a
The following paragraphs.
 Search code - in this menu you
can specify the character code, which you would
would replace (in the decimal system
radix)
 Replace code - well, and then you enter the code
character, which you need to replace the found character
 sIngle convert - start conversion
on the above parameters.
 Med conver - start conversion
Text from the Format Editor Kowalewski
MicroEditor the normal encoding
 Tablic convert - start conversion
Text on a pre-loaded table.
If the table has not yet been loaded, then
will be done loading the table.
 Load tablic - Loading Table
conversion. This table should
be up to 256 bytes and have a very
simple format, ie in place of the symbol
(Starting from zero), which should
replaced, should stationed character code, which must produce
replacement. In the author's delivery prilagayutsya four 
tables: DK-7BIT, ISOLAT-1 KOI8-R, WIN866.



   Extend Code Killer V1.0

 Well, this overlay is designed to
delete any characters from the text, as well as control 
characters ZXWinWord. Just want to make a reservation, the 
algorithm remove the very symbol of the brake, but very short, 
which put in these conditions in the first place. For

example, say that the removal of control characters in the 
description editor it took 5 minutes 25 seconds. A

Now about the menu.
 Erase code - enter a code symbol to be removed (in the decimal 
system radix)

 Single killer - run delete text you entered the code symbol
 eXtend killer - start remote control codes ZX-WinWord.

 For all questions about the editor and the file
addition, you can contact me
at the following addresses.
 Fidomail: 2:5057 / 21.36 To: Max Shashkin
 Subj: ZX-WinWord
 Snailmail: 443110, Russia, Samara,
st. Chelyuskinites 19 kv.40 Shashkin Maxim

Or telephone (84-62) 34-82-92
ask Maxima

 2000 (L) Copyleft, "STARS OF KELADAN"