3Bit #01
03 января 2005 |
|
Zhelezyachki - Something about the CMOS-clock: a modified scheme of Alone Coder'a.
Something about the CMOS-clock (C) AlCo Hello, All! Here, at the insistence of Cyril Frolov had to make the scheme a signal M1, the benefit, remained the failure to involve an element of Lesco. And thanks to his own post that Dallas is not too steep, is "Option 2". Now it is possible for the programmer a little more freely refer to on / off access to the clock, which can lead to the emergence of glitches in those who did not finalize a watch from you! However, leave it on the conscience of the programmers. CMOS-clock. Standard Ports "GLUK". # EFF7 bit 7 - the inclusion of access to the clock # DFF7 - a record in the CMOS cell address # BFF7 - read (write) data from (a) CMOS Option 1. 10 22M KR512VI1 quartz at 32.768 kHz 20 February OS1 RTC 3 OS2 470K 1533LE1 M1 February 1 1533ID7 March 1 1 A12 A0 DC 15 A13 2 A1 14 A14 3 A2 13 Jan. 11 12 December 13, 1917 DS 11 A3 4 v1 August 10 January 10, 1914 AS / OIRQ 5 v2 September 9 A15 V3 6 July 1915 R / W 5 1 April 1913 cE / WR 6 4 AD0 5 AD1 6 AD2 / 7 AD3 9 C TT 1533TM8 D0-D7-8 AD4 RESET 1 R 9 AD5 10 AD6 D0 Q0 D1 4 2> 11 AD7 / Q0 3> D7 5 D1 Q1 July 18 rES / Q1 June 1K bps to 20 CKF 12 D2 Q2 1910 1K 22 PS / IRQ 19 / Q2 11 E 13 D3 Q3 15430 KT315 SQW 1923 / Q3 1914 10K CKOUT 21 +5 V> Vdd Vss 24 12 KD522 +3 V Battery> D311 (D9) - using batteries with a voltage less than 4V, this diode must should be a germanium! At higher voltages You can put KD522. The signals from the legs 2 and 3 can be fed TM8 the scheme ext. graph. mode 512 * 192. Then from the scheme can only KP11 and IR23. Actually shemka connection legs 18, 20, 22 bit is incorrect, but it works well. So it was with Gluck, and currently I have done so - was too lazy to do it right. (True, from Gluck's clock feed only on battery 4.5V) And in the good should be used as follows: KD522 D311 +5 V> <+3 V battery 10K 20K a diode 24 Vdd KD522 <22 PS 4700 4700 1920 CKF 18 rES And if you plan in future to modify your favorite computer, so that it includes the signal clock CMOS (all software support is already in the firmware MADROM by AXLR), do not be lazy just do as necessary. Option 2. Those who could not get such as rulez KR512VI1 and dig out of the HRC "Dallas" or some other foreign analogues have stay on it. Although VI1 in such inclusion would be easy to work with;) 10 22M KR512VI1 quartz at 32.768 kHz 20 February OS1 RTC 3 OS2 470K 1533ID7 1533LL1 / RD 1 January February 3 1917 DS 1 A12 A0 DC 15 A13 2 A1 14 4 1 A14 3 A2 13 May 6, 1915 R / W 12 11 1533LE1 A3 4 v1 10 February 1 January 1914 AS / OIRQ 5 v2 September 3 A15 V3 6 July 1913 cE 5 1 4 / WR 6 April AD0 5 AD1 6 AD2 / 7 AD3 9 C TT 1533TM8 D0-D7-8 AD4 RESET 1 R 9 AD5 10 AD6 D0 Q0 D1 4 2> 11 AD7 / Q0 3> D7 5 D1 Q1 July 18 rES / Q1 June 1K bps to 20 CKF 12 D2 Q2 1910 1K 22 PS / IRQ 19 / Q2 11 E 13 D3 Q3 15430 KT315 SQW 1923 / Q3 1914 10K CKOUT 21 +5 V> Vdd Vss 24 12 KD522 +3 V Battery> D311
Other articles:
Similar articles:
В этот день... 21 November