22.02.99 Mordovia
Dear Nemo!
After looking at the HDD-IDC schematic in ZX-Format No. 8, I have a few questions:
- Are the inversion marks for the IDR, IDR/, 10W, and 10W/ signals shown correctly everywhere?
- Is the AST signal in the schematic АСТ?
- Are the CS1 and CS2 signals in the schematic CS0 and CS1 on the hard drive connector?
- The A3 signal comes from the system connector in the cable bundle, but it doesn’t appear anywhere in the schematic (11н D 6.2).
- I don’t understand what the designation МА1 refers to on the right-hand side of element D 6.2.
- Can 1533-series chips be used (D3–D4)?
I’d also like to know whether anyone has looked into using a hard drive with this interface to work with TR-DOS disks; and where, from whom, how, and at what price one can buy the latest versions of IS-DOS Classic 4.0 and ISDOS CHC 4.0.
One more question: could you send me the schematic for the IBM keyboard controller, including its ROM firmware (I’m sure the schematic has it), or publish it in the next issue of “Format”? By the way, can it be used without an additional driver?
Thank you in advance for your reply, and best wishes for the upcoming holiday.
P.S. Please send me a price list for your products or let me know the exchange rate.
I’m enclosing a self-addressed envelope for your reply.
Dear N!
- There are misprints in the schematic, which were the editorial staff’s fault at ZX-F. They were given the production files, in which the errors had been corrected. This is really a technical issue connected with publishing and its specifics.
After a schematic has been typeset, one more step/person is needed: a technical editor. One person simply can’t catch all their own mistakes—another person’s “fresh” eyes are needed. If the public paid for software, they’d have a technical editor too... You’re not the first to spot these errors; if I’m not mistaken, there are three of them. They’ll be listed in ZX-F No. 9. I can help you by sending you the schematic.
-
Using 1533-series chips is not recommended. It’s a very good technology (ALS) and a good factory (Integral, Belarus—see what it means to have no Soros in Belarus!), which is still operating normally (!). The 1533 series has a higher speed and a faster signal rise time at the output, which has a bad effect on the cable (and the hard drive, accordingly): it becomes a “long line,” with interference as well. In practice, there’s a high likelihood of unstable operation.
-
Working with TR-DOS disks is possible on the KAY-1024 through the “electronic drive” “C,” at the level of “blanks”—that is, as IS-DOS data-type files (not executable in the OS itself, but usable in every other sense), with the .trd extension. Returning to the system is, of course, impossible; in other words, IS-DOS works as a fast loader for TR-DOS disks from the hard drive. There probably isn’t any other way at all; in principle, it’s impossible, since TR-DOS recording isn’t OS recording (IS-DOS or any other hypothetical OS)—there are no “OS-related” fields there.
-
For ISDOS, see the subdirectory.
-
If I’m not mistaken, the keyboard controller was described in the 1995 issue No. 5 of the magazine “Радиолюбитель”/“Ваш компьютер” (see what it means to have no Soros in Belarus!). The firmware isn’t included; it’s identical to the one from “Profi” and works only with an XT keyboard. The question...
The reasoning that it would be used in TR-DOS is far-fetched, since the device emulates a conventional keyboard. What’s more, both keyboards can be used together, or you can use a Sinelair (Cursor joystick via the standard DB-15 connector).
As for the firmware—how am I supposed to send it to you? It would have to go by parcel post, which means 60 rubles for postage. With the IC, the total comes to 65 rubles. I don’t have the firmware as a file, so I’d have to “download” it—but in what format should I give it to you? And anyway, what are you going to do with an electronic file? It’s only 2 KB... I could print it out, of course... But you have to admit, all this is too much trouble for a single order. Electronics costs next to nothing nowadays, while time keeps getting more and more expensive. Today, this kind of operation just looks idiotic...
It’s profitable to trade in (and manufacture) standardized, mass-produced products with a very low production cost, using a standard, tried-and-tested process (which also takes very little time), and consequently keeping costs low. That’s the essence of “high technology.”
(c) Nemo. 03.03.99
P.S. The XT-KLAVA is currently out of production, as it has become obsolete. We’ll probably have to wait six months to a year for the “old shit” to clear out and the price of keyboard controllers to go up. Then we can make a good product that pays for itself, one we won’t be ashamed to sell. Maybe I won’t be the one to make it...
╔═════════════════════════════════════════════════════════════╗
║ ° ° ° ║
╚═════════════════════════════════════════════════════════════╝
Share your thoughts about the article