Mporady update +J
If picture interference is bothering you:
-
External interference, not originating from the computer. It could come from a disk drive, a VCR, or another computer. You can identify the source by turning off all devices except the computer and television, then switching them on one at a time.
Elimination: Move the device farther away from the computer; connect it to a different power source (e.g. a more distant outlet); ground the chassis; galvanically isolate it from the computer; shield the device (e.g. with aluminium foil); use a higher-quality video cable (e.g. with foil-and-braid shielding, better dielectric, a thinner signal conductor, and thicker insulation); use a better ground connection (e.g. by using “F” sockets and plugs). This type of interference is the hardest to eliminate. Sometimes the device itself needs to be modified, for example by fitting suitable filters.
-
Internal interference:
a. Related to inadequate shielding of the video path against interference, e.g. running an unshielded video lead parallel to and close to a source of interference.
Elimination: Shield the video cable (including externally), or improve its quality; remove the source of interference or move it farther away and shield it (e.g. shield the bundle of cables running to an add-on installed inside the computer); fit a ferrite bead on the interfering cable (all frequencies above 3 MHz should be attenuated, except for the ULA and Z80 clock leads and the colour crystal); run the interfering cable perpendicular to the affected cable; shorten the leads of the affected and interfering components; shield the affected and interfering components.
b. Related to incorrect power and ground connections.
Elimination: Replace the power cables with thicker ones; use filtering capacitors (0.1 µF, tantalum ones! Pay attention to their polarity and connect them as close as possible to the source of interference, e.g. right next to the processor, a 74xx chip, etc.). Capacitor leads should be as short as possible. The capacitors may have a lower capacitance, but there must then be more of them; this is a more beneficial solution. Use 0.1 µF per two 74xx chips. Fit ferrite beads on the power cables. The ground should be connected with thick wires, according to the diagram below:
74xx 74xx 74xx
I I I
I I I
I I I
O-----O-----O-----O
INCORRECT
74xx 74xx 74xx
I I I
I I O-----O
I O-----------O
O-----------------O-O
CORRECT
-
Interference from external peripherals
Elimination: The rules described earlier apply here, plus connect the video-signal lead (if one exists) to the peripheral nearest the computer. If the peripheral has a pass-through, its pass-through should be disabled for contacts (looking into the slot), underside: 11, 12, 13, 14. Do not trust the FDD station cable that carries the video signal; the signal should be taken directly from the computer, either as an amplified signal from contact 13 or directly from contact 14. The exceptions are 128+, 128+2, 128+3, where the signal can also be taken as digital RGB. If the video signal is taken from the computer, it should not be routed onto the bus.
-
Interference from the chrominance signal (observed on black-and-white monitors).
Elimination: Unsolder the colour crystal (approx. 4 MHz; don’t confuse it with the ULA crystal!!).
-
Interference from a faulty sound modulator (only models 128+, 128+2, 128+3)—manifests as no sound and interference in time with the music.
Elimination: Replace the crystal (6 MHz for Western audio, 5.5 for Polish audio), check…
-
Reflections
Elimination: Reflections are caused by a mismatch between the receiver and the signal; the signal is reflected back. Usually, shortening the video cable and improving its specifications helps. I don’t know any other methods.
-
Interference caused by an unpaid electricity bill (manifesting as a black screen and a bailiff).
Elimination: Don’t eat, don’t drink, don’t breathe—pay the bill.
-
Other interference, e.g. caused by the demo “Mercury Lamp”.
Elimination: A hammer.
Małyrules
Share your thoughts about the article