DO IT YOURSELF - BOUT SCART.

=========================================================DO SAM=====
                                                        
 ['BOUT SCART]
I found out that specs can be connected to ckapty
a long time ago, I don’t even remember when it was, but now
I did it much faster, now I’ll tell you how it went
was...                                                 
                                                        
by the way, specman, if you don’t know what it is, then it’s
such a rectangular connector with twenty holes is alive
it is mainly on TVs and VCRs. through him yours
TV and VCR copulate.                            
                                                        
(like fucking)                                   
                                                        
well, then I had my zxCh8 (well, which I often
beat), and I had a friend Vova, I have a normal one
there was no TV, but he just got one, it was called
he is horizont (made, obviously, in Japan), well, like new
Russian TV, square and withremote control and with ckaptom.    
                                                        
a shows crap.                                
                                                        
I didn’t know about the rgb input then, but I knew about video, and
That’s where I wanted the subclavicle to be connected. I'm colored then
I’ve never seen a speck before! Well, let's go to the store with
cables and found one like this there, on one scart a on
another five-pin, well, we thought it would do! (?)   
                                                        
we connected the whole thing, I clicked the switch,
The power diode on the power supply lit up, and nothing happened
shows.  Well, what to do, we took my spec and wire and
let's go to the zx service workshop, to Uncle Pasha.             
                                                        
I'll make it right now - he says, you're like a pack of Marlboro!
We flew out for cigarettes and he re-soldered this wire for us.
we brought it home (well, I’m not plowing, obviously), turned it on
again and again - there is nothing, av-mode and that’s it!               
        well, that’s where my enthusiasm disappeared, we gave up on it
case, and after a while I saw in a magazine
Scart wiring, current without kommehtcob of course... but to
For some reason we didn't connect to horizont, I don't remember
even what happened, maybe my spec is already broken a
maybe not that's why.                                       
                                                        
In short, in 1995 we bought ourselves a normal TV set,
so handsome, 21', and most importantly his rear is next to the rca
was attached and scart!   (that's why he told me
I liked it)!  There was this TV (and now everything is ok with it)
Chinese company amcol, look and it shows cool,
at least its body is from a Toshiba TV series
black fs, I personally saw one like this, they were probably useless
develop the body...                
                                                        
here I soldered the video signal from the spec to the twentieth
contact and everything worked! wow, cool - finished video
There is an entrance, no need to add anything yourself!  a,
I remembered, I still don’t have a scorpionit was, but somehow
my forty-eighth plowed, hung up every five minutes, but
what can you do - there is no other way, but at least look at how
The game loads and your soul is lighter!                       
                                                        
by the way, I soldered the same wire that we bought in
store, and it was one meter long. very convenient.      
                                                        
well, when I saw the scart's wiring, I noticed that
there are also rgb inputs, so I immediately wanted it
try connecting to the TV in color, and finally
find out what it's like - color speck!                         
                                                        
in the magazine, the wiring was npokomehtupobaha briefly, and
Nothing was explained there, just r-input, g-input, etc.
well, I took it and just connected the rgb output of the spec to
TV.  and nothing worked.  I asked Pasha, he
says that it also needs some kind of synchronization
connect, the place on my board where this synchronization
You can take it off, he showed it to me.                                                          
Well, where should it be connected? I plugged it into the video input
(where else?), the screen turned bright white and nothing
ordered.  By the way, on that piece of paper it was also written
about the “window” mode, some kind of contact there in this
I switched the mode, five volts had to be applied to it.
I tried it - nothing works.                          
                                                        
this mysterious window is missing!                            
                                                        
and so everything died out.  and then, oh miracle - Pasha gave me
a printout, on it was an article from some newspaper about
how nada connect! after a couple of years I found out that
it was a newspaper - on line (I found it by accident)! in
in this wonderful article, the person clearly explained what
where should I connect it so that everything works!                   
                                                        
forty-eighth had already died (did not live), and I already had
scorp, but anyway, thank you, man!                 
                                                        
кому не тeрпиццa, вот оно:                              
                                                        
                                                        
| 01-sound out (right)                                  
| 02-sound in (right)                                   
| 03-sound out (left)                                   
|-04-gnd                                                
|-05-gnd                                                
| 06-sound in (left)                                    
| 07-blue in                                            
| 08-tv/video switch [+12v]                             
|-09-gnd                                                
| 10-not_connected                                      
| 11-green in                                           
| 12-not_connected                                      
|-13-gnd                                                
| 14-not_connected                                      
| 15-red in                                             
| 16-av/rgb switch, [+3v]                               
|-17-gnd                                                
|-18-gnd                                                
| 19-video out                                          
| 20-video/sync in                                      
                            not_connected is like unemployed, and gnd is
general, ale - earth (in the porthole). as you can see here
there may even be a signal to switch the TV from TV to
video, but they probably don’t use it right now.  here you go,
connect rgb signals to pins 15,11 and 7,
The sync mix is connected to the video input, and you can do the same
connect to av/rgb switch, well, it fits quite well,
In short, you close 20 and 16 and connect sync there.         
                              
you can also put cutters in the rgb gap,
select nada from 0.5 to 3 kilograms to taste, so as not
it was too bright, but I finally didn’t put anything on, and so
will pull!                              
                                   
but you can connect to this switching contact and
just +5v current through a 470ohm connector to make it work
about 3v, here. So why is this... currently it was also written there that these are connected
signals may not be present in all TVs, such as current in
European (ale Philips) everything will definitely be the same in the rest
scart may also have video/audio inputs -
outputs.                                               
                                                        
that's how it was on my TV. then the author suggested
find a video lamp on the TV and its description and connection
straight to her, all business! for example he told
about the toshiba ta8659 lamp, a common one like this:   
                                      
this is the type of her legs: 47-red in- 49-green in- 51-blue in-
53-av/rgb switch- 50-gnd                               
                                                        
currently connect everything through strips, on r and g at 820
ohm, a to b - 1.8 kiloohms.  select a on switch
experimentally, start with 500 ohm, until you cut it
inclusive.  a, also connect the capacitors to the rgb (in
gap, obviously)you can put 0.1mkf and you can
others (try and see).  and check if they are closed
rgb inputs to gnd (50 leg), if so then otomkhu.         
                                                        
and you won’t believe it, guys - I’m so lucky that I have
this particular video-proc... that is, a lamp!  I bought
wires, rubber bands (put them in different pockets so that
don't confuse which is which, I'm not at all into them
figured it out), and when my mother was not at home, I opened my
tele.  It’s so scary, suddenly something breaks! I found
processor, and there are direct platforms for the wires, and
under the rubber bands too, there are no current rubber bands or wires, but
The processor's rgb inputs are connected via connectors to gnd. a leg
switch av<>rgb it’s finally unclear where to connect, although
Scart also failed in the end.             
                                                        
well, I can’t tear it off from where it was attached
became, and simply connected it with a wire to the scart. collected
I him (time was running out, mom could come back and knock
I'm crazy about it - I've already got into the new TV with my own
rake), turned it on, but nothing works. i.e.  when you switch to av, the picture (color!)
appears for half a second and searches.                        
                                                        
then, later, I climbed into the TV together with crash
again, as I expected, it was a matter of hoxe -
switch, immediately some kind of rezik came from it,
I found out that it was ten kilo-ohm, and then it connected
to the rest of the circuit, and immediately after the rezik he went to
scart.  but then I didn’t even have a tester and what is this
I didn’t know the rubber.  I took it and soldered it to this rezik
jumper, short-circuited it simply, so it didn’t interfere.    
                                                        
we cut the spec, once - and it all worked!!! color
speck!!!!!                                               
                                                        
we quickly assembled the TV, and then I noticed from the screen
graphs stretch on the right, black 'tails', almost to the end
screen.  and soon mom was supposed to bring it in! but here
I connected the scart and the tails disappeared. in short kada switch
If it is connected to the video input, then everything is ok, but whenno, then
tails.   This, of course, is because I’m this rezik
neutralized, I didn’t do anything else.                
                                                        
but I left it like that, it doesn’t interfere at all. and I became
Every day you sit on it with great effort and drag, drag!
then they bought me another TV (hitachi), and amcol
this parents are watching themselves right now, I spent some time during the day
I ran into their room during the day, but then my scorpion broke
and there was no need to run there.  a new one I have right away
a monitor appeared, and now I have to carry it around in a pussy
the drawer in that room is problematic, too bulky!       
                                                        
sorry...                                               
                                                        
I made a little spec just now, so now I'm probably with it
I’ll hang out there sometimes now, I’ve already made the cable (today
by the way!), beautiful, three meters high...                     
                                                        
and scart there and rca, and on scart there is a toggle switch, it switches
rgb mode, then just a video signal (from the pal encoder there
signalconnect)                                       
                                                        
o, by the way, would you like to tell me a joke? about five days ago I went
I'm going to buy the wire for this cable in the store,
there is a stand with wire samples in the corner, look at what
you need it and then tell the guy his number, and he gives you
his nputackubaet jumps over meters and writes out a piece of paper
with the price, go to the cashier with it, pay, take the receipt and
you take the goods from the man.                                
                                                        
well, I look, number 35, seven wires in the screen, 14 rubles/meter.
and the business was closing, the sellers were all so steamy,
tired, freaks!  I tell him - ..., three meters, he
brought it, wrote out a piece of paper (42 rubles), gave it to me, I carried it
took it to the cash register, gave it to my aunt and gave her a 50 ruble piece of paper. a she
asks - do you have two rubles? I say - eat it, put it in your pocket
I went after them, and she said - maybe twelve
will you find it?                                                 
                                                        
I say, I’ll find it, I gave it to her, and she gives me mine
fifty kopecks_(!) and gives a check!Well, of course I grabbed the wire and
We got out of there in no time!  in short, just a four
very much looked like a unit!  like this
The cunts work for Sergei Bilkov.