ZX Konig #02 31 декабря 1994

Софт

of Compliance - A Brief Annotated to the program layout and PCB layout - LAYOUT NEW.

 Short abstract to the program
for layout and wiring
PCBs:


        L A Y O U T NEW


    (C) Vlad Sharamkin 1993

1. History of the creation of the program:

 Three or four years ago in
my collection has appeared
an agenda LAYOUT,
or rather not even program a
prefabricated. All the descriptions in it
were in German, but
within the meaning can be seen that
program is designed to
work on the layout of printed
boards. In general, little interest
I was not shown to her and LAYOUT
went to the archives. However,
Soon, circumstances have forced
re-think about it. And now
then I woke up again
interest in this programmke. Immediately
it became clear that in
original version of the program
simply not suitable to
use. This was attributed to
so, not knowing the German language
make it something it was
simply impossible. And then, c
head to toe levy
technical German-Russian
dictionaries, I set
work ... During the transfer were
found a rather rough
errors in the program, as well as
lack of support for the printer.
After the end of LAYOUT
BETA has been given for testing
great expert on the assembly and
Speccy adjustment in our city
Sergei Kozlov. Thanks to his
valuable comments of the program
become more comfortable in
treatment and acquired some
new features.
 Thus the final
version of the program was
called LAYOUT NEW and
represents the following:

2. A general description of the program:

 Program LAYOUT NEW
intended for both
Professionals in electronics,
and for most beginners.
 With this program
can be fully automated
manufacturing process of printed
motherboards, starting with the selection of details
and ending with printing the final
board layout on the printer, and
in full size. AND
lets do it in
several times faster, and most importantly
convenient to similar programs such as
PLATA, and like her. It was
possible due to rapid
calculation algorithm and especially
so that the program was not written
in BASIC-e, and the ASSEMBLER-e.
 Interface, LAYOUT very simple,
and the function of each item is clear
from its description in the menu.
 The program has a built-in
functions to work with printer
the interface ZX-LPRINT,
lets you print lists
compounds, and detail as well as
pressing the [P] mode
viewer willing to pay, you can
obtain a copy of the paper and board
in full size.
 The opportunity
use two disk
drives, and some others
smaller additions.

3. Brief technical
program features:

 Maximum Dimensions
dresses are made: 200 X 200
mm.
 The maximum number of
connections between the elements: to
1000.
 The maximum number of
elements on the manufactured
board: up to 1000.
 Ways to PCB
Conductors: 3.
 Using the types of elements:
B1neogranicheno # # b0.
 Speed ​​routing: different and
depends on the method and amount of
compounds.

4. The general procedure for
creation of the PCB:

 1. To the program information
about all types of items
needed to produce
Boards (name, size,
number of pins, the distance
between terminals, etc.).
 2. Enter into the program information
about the connections between the findings
items placed on the board (
eg 04 DD1 - DD7 and 13
etc.).
 3. Introduce a dress size
the required fee and be placed on
It all used items (
when you click on the button [C]
showing the connection between
conclusions of elements).
 4. Choose a method of wiring:
one-sided (on either side
from the elements) or double-sided
and run the calculation wiring.
 5. Upon completion of wiring
reconstituted board can
view and print with
different sides, with the imposition of
large-scale grid, with different
increase, etc.

 Exit from any menu
done by pressing the button
[Q].

5. Wishes of users
Program:

 This review article I
try to give you only a general
representation on the appointment and
features of the software LAYOUT
NEW.
 And in conclusion I want to give
some tips for
Beginners:

 1. Do not forget to save
its results to the
disk.
 2. Turn on the printer before
starting the program, not in it
itself.
 3. Rational place
the layout of your card before
wiring.

Well that's basically it. I wish
all the luck in working with the program
LAYOUT NEW. I'll be very happy
if you like it or bring
benefit to someone out of you.

Their opinions about the program can
sent to the publisher.
Specially for


         "ZX-Kenig,


  Vlad Sharamkin 13.05.1995g.