EMS 2.00 - About the correct setup of SETUP.

╔════════════════════════ ═══════════════════ ═══════════════════╗
║  EMS 2.00 in Moscow.       ║
╙─────────────────────────────── ───────────────────────────────╜
(C) EVP-SOFT

 Hello everyone.  I decided to tell you about the correct setup
SETUP, by the way, there is now driver 2.32+, and with it at EMS 2.00
determines numbers without modifications to the modem. You just need to do it right
configure SETUP.

The first two lines of SETUP are needed only by owners of Kempston Mou-
se:

"Auto view"
Defines the EMS actions when you double click on a file, namely
viewing it as text or as a dump.

"Double click delay"
Double click speed.

"Floppy driver"
Turbo - will be faster to read/write and catch errors, after "No
Disk" drives will not spin until the floppy disk appears, but
Normal can work with HDD. By the way, if on your drives
CONVER 4.61 corrupts disks, but EMS can do the same when recording
most.

"Ring-answer delay"
Delay between the start of a PBX call and picking up the handset on the modem,
ifIf you pick up the handset during a call, the modem may shut down.
For Moscow automatic telephone exchanges, 65 is desirable.

"Number of requests to ATS"
The number of requests to the PBX to determine the number is about 7. Possibly
but, of course, more, but in 99% if the number is not determined with 6 entries
dew, then it will not be determined even after 200. Moreover, if you set
there are many requests, then if the number is undefined, the calling subscriber is
will immediately understand upon hearing requests.

"Digits in phone number"
The number of digits in a phone number, this is necessary for their correct
output after definition.  In Moscow, as you know, numbers 7
significant.

"Delay before detection"
Delay for switching processes when picking up the handset. According to GOST
this is 25Oms, but electronic telephone exchanges allow up to bOms. If the delay
is small, then the operation of Caller ID is almost imperceptible by ear, but the automatic telephone exchange can simply
not hear the first requests or, more often, the modem may not hear
answer.  With a large delay, everything is OK, but Caller ID work is well-
noticeable to the ear. For a good definition, put 2SSms.

"Line sensitivity"
The degree of reliability of recognition of short and long beeps.
If the number is high, EMS will only recognize those that are ideal across all
beep parameters, when the number of beeps is lowmay be accepted
any noise on the line. Usually around 6..12.

"Answer sensitivity"
The definition of the number depends on this constant. This is an advanced degree
accuracy of response recognition. If the number is small, then for the answer
Any noise can be accepted and instead of a number there will be complete nonsense.
If the number is large, then a weak response may simply go unnoticed
and EMS will write "Can't detect phone number". This parameter is necessary
configure individually for a specific modem, but usually this
around 17.

"Interdial delay"
Interdigital pause when dialing a number, according to GOST - 6OOms, but on
Most PBXs can be set to less than 4OOms. It’s just that if interdigital
If your pause is too short, you will often hit the wrong
yes.

"Pulse period"
Dialing speed increases as the number decreases, but
On older PBXs, dialing accuracy decreases.

"Tone/Pulse"
Tone or pulse dialing, but the driver supports
only pulsed.

"Redial attempts"
The number of auto-dial attempts, after their number has expired, auto-
The dialing stops and the message "Dialing" appears in the terminal
failed."

"Line check delay"
Number of requests to the server.  Considering that usually the server
picks up after 2 rings, then about 15. If less, then ask
sy may end before auto-raising, and if more, then at low
However, this will not help the connection, it is better to call back immediately.

"Line volume"
Speakerphone volume (don’t be surprised, it’s via AY), at high
volume decreases intelligibility.

"Redial delay"
Pause between auto-dial attempts so that someone can call you
thread.

"Number of rings"
Number of calls before picking up the phone. Usually 2, if 1 then maybe
there may be false positives when hanging up on the phone. By the way-
here 0 = 256.

"Auto off line"
Time after which EMS will hang up if the user
the body does nothing. Each unit is equal to 8 seconds. For example
measures, to set 3 minutes you need to enter 23. If 0, then the time is not
limited.

"Connect speed just"
When set to Yes, the server will transmit at the speed at
which he accepts.

"Block length control"
The same applies to the block size, or maybe not. Place
Yes.

"Attempts before error"
The number of reception errors before the file download is interrupted.

"Split file length"
Block size, 128 or 256 bytes, communication is usually more reliable with 128,
but there are strange exceptions.

"Key sound"
Sound when pressing keys: AY|Beep|None

"Call sysop sound"
Sysop call sound: AY|Beep|None

"Russian layout"
Here you can make any Russian keyboard layout for termi-
nala.

"Editor kbd layout"
Definition of the Russian layout in ZXWord: yaverty|ytsuken

"Log auto save"
If Yes, then when the log is full, it is written to disk.


 However, if there is a parallel Caller ID, then the numbers are not determined in the EMS
Yes, but this is a hardware feature of the modem. Although if
you have Caller ID version RUSS-23, then you can set constants to arrange
understanding of this conflict.
   But first, let's look at the cause of the conflict. And the reason is simple -
Usually, when caller ID detects a number, it loads the line, and the company
modem speaker with additional load on the lineusually not
can accept the PBX response without errors.
   So, it is necessary that Caller ID does not load the line. And in the version RUS-23
this is provided.
   First, set the normal mode (**1), then turn it off
line load (**37, "S"=OFF). However, you still need to turn it off
pronouncing the number in Normal Mode, and not as a constant
"E"(**39) - it has no meaning here, but by setting
constant "c"(**39) to 0 (this is apparently a glitch, because when the caller ID says
into the line, it is clear that it loads it, but when on the speaker
?!). And it is advisable to turn off requests on Caller ID (**38, "J"=00), because
otherwise, it may turn out that Caller ID will clog up with your request
reply to EMS request. However, turning off requests on Caller ID is not at all
means that Caller ID will not come out to determine the numbers, it will determine them
will be listening to the response to the EMS request, only sometimes you need to pick up
the first two constants in (**34). And yet, some Caller ID cards are not
allow you to determine the number without load on the line (if **37,
"S"=OFF).