==========================================================HI-TECH=====
CUTTED'N'BENDED
how to work with iron? interesting question. well here's to the elephant
Right now, for example, we need to attach 3.5 disk drives. and he has a box
from a corvette. the board is screwed to the bottom. I thought that under
drive, you can cut a hole in the left side of the front
panel of the case, and secure it so that we need to make something like this
a piece of iron bent at an angle.
i.e. on one side of this piece of iron will lie
disk drive, and its other part is bent at an angle of 90* -
fasten it to the front panel with screws. well not really
the disk drive will lie on it - it will be towards it from below
screwed. in short: the drive will be visible from the outside and a little
Below are a few screws.
explained as best he could, those who didn’t understand were not to blame.
I can’t get any clearer no matter how hard I try.
so how to make this piece of hardware?
first, measure the width and length above the bottom
disk drive, plus another two centimeters on
"bending". The result will be a shorter rectangle.
now we need to find a sheet of iron of suitable size.
Aluminum stands out here, a very soft metal, with
increased thermal conductivity. pilitsa and sverlitsa very
It bends easily too. but also from ordinary sheet steel
You can also build something, although it’s more difficult.
take, for example, a marker and a ruler and draw on a piece of iron
outline of the required size. and the fold line is folded too
draw.
sawing metal so that there are special saws -
hacksaws for metal. the garbage itself, which actually
nags, replaceable, so you can change it whenever you need ityou'll break it or
dull it. I have never had a dull saw before,
everything has broken before!
I broke the last one in the fall, when my stupid one and I
friend stole a picket fence and tried not far from
place of theft, cut off two separate pipes from it (he
I wanted to make two T-shaped stands out of them at home
under the bar)
o, by the way, guys - I heard that there are files for
jigsaws, not for wood but for metal - who knows
tell us a few words (what they are / area
applications / how to use)
The place for sawing should be discussed separately. here you go,
Place the piece of iron on some kind of thread, for example a table. current not in
room and not in the kitchen table, but on the left one. or
- best of all - go out into the yard and do “this” on what -
thread on a table or bench.
holding it tightly with one hand, try to make it with the other
shallow first cut. by the way, it’s better in advance
make with a file. the saw should be deepened by a millimeter
into metal. keep doing this - with every jerk you saw
It will bite deeper and deeper. a down will be
sawdust.
regularly check that the pipe is straight.
When you get a little tired, take a break. think o
pleasant and incomprehensible. swipe expedition
depths of the nose.
but you finished it to the place where you need it - it would be a saw
unfold. but this is not a jigsaw and it just doesn’t work
unfold. Here we need to act more simply. along that
lines that you couldn’t turn the saw to
a couple of holes as close to one another as possible, then
File the partitions between them. and here on
there is now a piece of hardwareoblong hole, just
along the line along which to cut. unscrew the saw from
one end from the frame and push it into this hole.
squeeze it back and drink.
as clearly explained.
In general, you have almost finished fasteners for
discot. current - you still have to bend the piece of iron! of course you
- did you mark the fold line with a marker? if yes, then here's how
you can bend it easily:
using the same drill, we drilled a number of holes right on this line
small, about three millimeters seems to be just right,
seems like such a perforation. you already understood
what do I incline you to?
of course yes. When many holes are drilled in a row, then
there is no way out. more preciselyThere are only two exit options - one
more accessible than others! most accessible - just take it
pliers and bend them, and you can clamp the piece of iron in
vice [if any] and the part that needs to be bent
knock carefully with something heavy. hammers by the way
there are special ones - wooden ones (at work in our school
there were such ones). This is just the right way to bend a piece of iron -
get it right!
other artisanal methods of bending pieces of iron have not yet been identified -
leno! Unfortunately.
I have everything on this issue,
saw and bend to your health,
after all, everything was given to us for this by God.
Share your thoughts about the article