pC>>ZХ - Since you are reading this, it means that you will now learn all sorts of interesting and not very details about writing corps.

============================================================pC>>ZX=====
                                                        
 'BOUT PC CASE
since you are reading this, it means that you will now learn all sorts of interesting things
and not much detail about the pussy buildings.            
                                                        
it’s no secret to kakora cnekmaha that cases for speck
are not produced in factories. so he is forced to live where
horrible.   in buildings shorter than some others
computers and other various cases ale - not from
computers in general!                                     
                                                        
most often zx cars were shoved into the body from someone
Corvette computer.   and for scorp it finally was
standard  Well, what can you say about this box? box like
box, plastic box in white or gray.
on the back there are holes for sockets, two compartments for 5.25 engines.
I don’t see anything particularly beautiful in this building.          
                                                        
if you somehow decorate it with something, then nothing!
what to decorate with?  well, put 3.5 in it, some thread
toggle switches on the front, buttons and of course,
some kind of LED, better two, one large, the other
small, connect the signal to some thread
for decorative purposes.  to wink at you.  explanatory
You can hang signs next to each one. or switch
put the power supply in front (so it's on the side)             
                                                        
but the most realistic option is a PC case. not yet
from anyone, of course...                                    
                                                        
their cases come in xt/at/atx standards. and in form -
here it is, the solution: before - not so long ago, there lived
386 and 486, they had real minitowers,
and there are many different options! design is design! here I am
It took me a long time to choose a case for myself, and now I’ve chosen it, and it’s standing with me
three years old, very cool, very handsome! could do it in short
do before the body.                                  
                                                        
a 286 and xt lived in their own branded buildings. often I
I see 286 in hugelying boxes. but there are already three
compartment for fives and one for three, current it is vertical
worth it.  I've seen several versions of such cases, but all
The only difference was the front panels.  by the way very
looking good. but it’s a painfully bulky box!     
                                             
but let's return to minitowers...                           
                                                        
you can fix the spec board on the bottom, lying down. and oh miracle
by the way - the size of a scorpion is ideal,
one-on-one!  finds the Pentagon - also suitable, but according to
length - end to end.  to secure the board to the bottom, press
drill four holes in this bottom by three millimeters.
hametb exactly where your holes are.                 
                                                        
oh, my inner voice wants to say something...
fellow wild spekmans!  I am the inner voice of trash.
I have a convincing request to you - attach the boards to
all four screws and fasten them smoothly, without nepekocob. a
then tresh often meets zx'ksa, in which boards
screwed, for example, with two screws andsomehow. what do you mean,
buhtukob, is it a pity?  and then you lay the board flat
nobepxoctb, and she’s lying there like an oar, all twisted.
That’s where the microcracks in the paths come from and that’s where it all comes from
following. and just sad... thanks for your attention.    
                                                        
so, drill holes in the bottom and put Zmm in them
The screws are long, one and a half to two centimeters. tighten them
nuts so that they stand straight up.  now we need to find
some old felt-tip pens or something like that.
we need from them the current caps or “plugs” that
they are stuck on the other side.                          
                                                        
pick out four plugs from them, make holes in them and
put them on screws (with the hole facing up, of course), if
The length of the plugs is not suitable - they are too long, which means
cut them with scissors and leave them somewhere around the corner.       
                                                        
and now you have real stands for the board.
now you can put it on them and see how it is
look!  and fasten it with the same nuts, current
from above.   in the case ofthe pentagon makes sense somewhere
make an additional pair of pins in the middle of the board,
current to insulate them from above with something, just because
it is very long and can bend, let them
they are supported from the bottom in the middle.                             
                                                        
there are sockets - on the back of the case there are just holes for
two sockets of nine contacts and two of twenty-five.
These holes are closed with glands, but they can be easily
break it out   but there is a better way.  normal nests
fastened on special pieces of iron, which are fastened with
one side buhtukamu.  under these pieces of iron there is in the back
appropriate hole shape.                        
                                                        
any writing card has sockets for these pieces of hardware
attached.  take an ega card for example, pick it out
from it a nest and fasten it together with this piece of iron in
body.                                                
                                                        
for example, I have two sockets of fifteen each (keyboard and
joysticks), one by nine (monitor), and one by 25
(printer).which I recommend to you too.                        
                                                        
and in general, where there are no sockets, there are so-called “stubs”, i.e.
pieces of hardware that don't have holes for sockets, they're just there
They are used to cover the holes. Yes, you can screw it up (really
too much) and dig holes in them for nests. but better
dig up broken cards and get everything from them for free and without fuss
tear it off.                        
                                                        
there is always a switch on the front of such a case
power, reset and turbo buttons (fixed) and
keyboard switch.  you can unscrew it and replace it
put a toggle switch, for example fdd1<>fdd2, etc.            
                                                        
the lock on the turbo button can be removed if you disassemble it,
everything is so simple inside, it’s immediately clear what’s going on
remove.                         
                                                        
threemulti-colored LEDs are often installed, turn them on,
I like it, I hung one on power and the other on
flash signal.  in general it was blinking really... until he speculated
died.                                                   
                                                        
but even now, even after he died, the diode is still blinking.          
                                                        
A two-digit LED indicator is often still available. us
it doesn’t fit right because there’s no way to include a comma
(I was dealing with this problem), so 3.5 / 7.0 is not there
depict. a pity.            
                                                        
I don’t care anymore.                                        
                                                        
you will also find a small speaker there. he's not for you either
needed.  pc through it nukaet, kada turns on and more
sometimes.  and since the Spectrum is turned on, it’s silent like a fish,
then he doesn’t even fucking need this speaker. Here.            
                                                        
and in conclusion, I would like to say that sometimes
which threads are branded PCs in branded cases, Hewlett
Packard, for example, likes to do this and compaq.  how
As a rule, they are recumbent, and look gorgeous! if anything
such a turn-up, then look for yourself!                       
                                                        
and the coolest thing is to make the case yourself, in your own way
idea, from scratch. but it's very difficult. but it is possible.   bye!