╒───·───════════════════════════════════════════════════───·───╕
│·▒█░█▒·▓████████████████▓ ·HARDWARE· ▓██████████████████▓·▒█░█▒·│
╘───·───════════════════════════════════════════════════───·───╛
(R) MAL'S
╔════════════╗
║ GRM+kb. ║
╚════════════╝
Install KR RU7 in place of KR RU5.
Disconnect signal C21 from pin 6D28 and connect it to ground.
Disconnect signal A8 from pin 4D28 and connect it to signal 7D34' from the circuit.
Replace chips D31', D34', and D80' with the following equivalents:
- D31' — KR3KP11
- D34' — KR3KP12
- D80' — KR3TM2
D34'
┌──┬───┬──┐
├───6─┤A0│MUX│YA├─7───── (1 D35-D50)
(4 D27) C21 ────5─┤A1│ │ │
┌─────────────────4─┤A2│ │ │
│ (38 D53) A8 ────3─┤A3│ │ │
│ ├──┤ │ │
│(14 D34) RAS ───14─┤S0│ │ │
│ (2 D34) VH1 ────2─┤S1│ │ │
│ ├──┤ │ │
│ ┌───1─oEA│ │ │
│ ├──o──15─oEB│ │ │
│ └──┴───┴──┘
└──────────────────────────────────────────────┐
D80' D31' │
┌─┬──┬─┐ ┌──┬───┬──┐ │
(9 D80) ─o─4─oS│TT│Q├─5────────────────2─┤A0│MUX│Y0├─4──┘
│ ├─┤ │ │ ├───3─┤B0│ │ │
(3 D80) PR ─┼─3─/C│ │ │ ├──┤ ├──┤
(2 D80) D7 ─┼─2─┤D│ │ │ ┌─────────────5─┤A1│ │Y1├7(4 D34)
___ │ ├─┤ │ │ │ ├───6─┤B1│ │ │
(1 D80) RES ─┼─1─oR│ │ │ │ ├──┤ │ │
│ └─┴──┴─┘ │ (1 D31) ────1─┤S │ │ │
│ │ (15 D31) ──15─oOE│ │ │
│ ┌─┬──┬─┐ │ └──┴───┴──┘
└10─oS│TT│Q├─9──┘
├─┤ │ │
(11 D80) PR ──11─/C│ │ │
(12 D80) D6 ──12─┤D│ │ │
___ ├─┤ │ │
(13 D80) RES ─13─оR│ │ │
└─┴──┴─┘
╔═════════════════╗
║ PENTAGON+kb. ║
╚═════════════════╝
Disconnect signal B14 from pin 5D16 and connect it to ground.
Disconnect signal A8 from pin 5D18 and connect it to signal 7D61' from the circuit.
Replace chips D16', D18', D61', and D62' with the following equivalents:
- D16' — KR3KP11
- D18' — KR3KP11
- D61' — KR3KP11
- D62' — KR3TM9
D16'
┌──┬───┬──┐
├───2─┤A0│MUX│Y0├─4───o─── (1 D20-D35)
(4 D14) B14 ────3─┤B0│ │ │ │
___ ├──┤ │ │ │
(1 D16) RAS ────1─┤S │ │ │ │
(15 D16) CPU ──15─oOE│ │ │ │
└──┴───┴──┘ │
D18' │
┌──┬───┬──┐ │
┌────────────────2─┤A0│MUX│Y0├─4───┘
│(38 D13) A8 ────3─┤B0│ │ │
│ ___ ├──┤ │ │
│(1 D18) RAS ────1─┤S │ │ │
│(15 D18) DIS ──15─oOE│ │ │
│ └──┴───┴──┘
└────────────────────────────────────────────┐
D62' D61' │
┌──┬───┬──┐ ┌──┬───┬──┐ │
(10 D13) D6 ───3─┤D0│RG │Q0├─2───────────2─┤A0│MUX│Y0├─4──┘
│ │ │ │ ├───3─┤B0│ │ │
(13 D13) D7 ───4─┤D1│ │Q1├─5─┐ ├──┤ ├──┤
├──┤ │ │ └─────────5─┤A1│ │Y1├─7─(5 D18)
(1 D62) ───1─oR │ │ │ ├───6─┤B1│ │ │
(9 D62) ───9─/C │ │ │ ├──┤ │ │
└──┴───┴──┘ (1 D61) ────1─┤S │ │ │
(15 D61) ──15─oOE│ │ │
└──┴───┴──┘
Port #FF modification in the GRM 2+ computer
This is needed so that port #FF does not interfere with reading data from the modem and other peripherals that use lines A3 and A4 to decode read ports.
If you build this, you won't need any diodes.
D56
┬──┬─┐
│DC│ o─15── D14
│ │ o─14──
│ │ o─13── ├──┤
│ │ o─12──(FFRD)─┬X──────────────────────────X┬─1─oOE│
│ │ o─11── │ │ └──┴─
│ │ o─10── │ │
│ │ o─9─── │ │
│ │ o─7─── │ │
┴──┴─┘ │ KP3ИД7 └─────────┐
┌─────────┘ ┌─┬──┬─┐ │
│ A3 (D34.3)──1─┤1│DC│ o─12──FFRD'(D14.1) ──┘
│ A4 (D33.13)──2─┤2│ │ │
│ ┌3─┤4│ │ │
│ │ ├─┤ │ │
└── FFRD (D56.12)─┴4─o │ │ │
IORQ (D56.5)──5─o │ │ │
M1 (D56.6)──6─┤ │ │ │
└─┴──┴─┘
The КР3ИД7 chip is soldered onto an identical chip (D56). Signals A3 and A4 can also be taken from the processor, but it is better to use the indicated chips. (There will be less wiring on the processor.)
The FFRD signal (port #FF select) is replaced with FFRD'.
I built this circuit, and it works fine.
╔═════════════════════════════════════════════════════════════╗
║ DON'T MESS AROUND: PORT #FF IS THE STATE OF THE DATA BUS, ║
║ NOT A PORT. REMOVE ALL THE CHIPS AND INSTALL RESISTORS AS ║
║ DESCRIBED IN ZX-Ревю No. 4/1995, p. 32. ║
╚═════════════════════════════════════════════════════════════╝
...Poor GRM...
----------------------------------------------------------------```
## Hardware
Fragment 3/3.
```text
╔═════════════════════════════════╗
║ CDOS modem can work better ║
╚═════════════════════════════════╝
┌───────────────────────────┐
│ ┌────┐ │
┌┴─┐ │ │ │
┤ │ │ │ │
┤ │ └────┘ │
┤ │ ┌──┐ │
┤ │ │У ├5─ │
┤ │ │Д │ │
┤ │ │2 │ │
┤ │ └──┘ │
┤ │ ┌─┐ ┌───┐ ▄ │
┤ │┌─────────┐└─┘ ┴ │ │
┤ ││ ЛЛ1 │┌─┐ █R1 │ ▀ │
└┬─┘└─────────┘└─┘ ┬ │ ▄ <─┼──receive LED
│ █C1█┬┤█R2█├■ │ │
└──────────┼──────┼───┼─────┘
│ __│__ │
└───┤_____├┘ R3
R3 = R1 + R2; R1 AND R2 ARE REMOVED.
THE OPTIMAL SETUP: WITH THE LINE IDLE, THE LED SHOULD BE OFF.
WARNING: When overclocking, expanding memory, and making similar
modifications, we recommend adding a way to disable all these
“extras,” so you won’t end up blaming programmers who don’t expect
your computer to be something that isn’t quite a ZX-SPECTRUM anymore.
╔═══════════╗
║ TURBO Z80 ║
╚═══════════╝
(3.5MHz) ┌─┬───┬─┐ ┌───────────── Z80:6
CLK ──────────────────2┤ │КП11 │ │
+5V ──────────────────5┤ │ │ ├4─┴─┤████├────── +5V
┌────┐ ├─┤ │ │
(7MHz) ┌─2┤ЛЕ1 ├1┬──────3┤ │ │ ├7───┤████├────── /WAIT
D2:9 ─┴─3┤ │ │┌─────6┤ │ │ │ (Z80:24)
└────┘ ││ ├─┤ │ │
┌┼┼─────1┤ │ │ │
│││ ┌─15┤ │ │ │
│││ ─┴─ └─┴───┴─┘
││└─────────────────────────────────────┐
│└─────────────┐ │
└────────────┐ │ │
D15:2 ───────────────────────┼─┼┬────────────┐ ┌────┐ │
┌─┬───┐ │ ││ ┌─┬───┐ └─5┤ЛЕ1 ├4─┘
+5V ───────────┬─1┤ │TM2│ │ ││┌─10┤ │TM2├9──6┤ │
┌────┐ ┌─┼─2┤ │ │ │ │└┼─12┤ │ │ └────┘
D15:3 ─┤ЛЛ1 ├──┼─┼─3┤ │ │ │ └─┼─11┤ │ │
D15:6 ─┤ │ │ ├─4┤ │ ├6─┘ ├─13┤ │ │
└────┘ │ ┴ └─┴───┘ │ └─┴───┘
│ █ 2K +5V ─┘ TURBO
│ ┬ ─┴─ 32+28
└─┴────────────────────┘ └────────────────────
D9 (ВГ93)
On the board, make one cut. Disconnect the wire going to pin 6 of
the Z80 and connect it to pin 2 of the КП11; then feed the processor
with the signal from pin 4 of the КП11.
·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙∙·∙··∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·∙·
·
∙
│
Share your thoughts about the article