| MSF #29 |
|
Железо - Назначение перемычек 3.5" дисководов.
назначение перемычек 3.5" дисководов форма записи: модель дисковода наименование джампера описание функции положение для разных модификаций одной модели положения джамперов могут отличаются. в таком случае указано две модификации модели и положение джамперов для каждой из них - pANASoNIC Ju-257-oЗT pANASoNIC Ju-257-oЗp Do drive selected as DRIVE o oFF D1 drive selected as DRIVE 1 oN D2 drive selected as DRIVE 2 oFF D3 drive selected as DRIVE 3 oFF Mo spindle motor controlled ьУ the motor on signal oN MS spindle motor controlled ьУ the drive select signal oFF DC disk change is the signal on pin 34 of the interface connector oN RY readY is the signal on pin 34 of the interface connector oFF TM terminator oN - pANASoNIC Ju-257A-o81p pANASoNIC Ju-257A-1o1p Do drive selected as DRIVE o oFF oFF D1 drive selected as DRIVE 1 oN oN D2 drive selected as DRIVE 2 oFF oFF D3 drive selected as DRIVE 3 oFF oFF Mo spindle motor controlled ьУ the motor on signal oN oN MS spindle motor controlled ьУ the drive select signal oFF oFF NC pin 2 of the interface connector is not connected oFF oFF HD HD is the pin 2 output signal oFF oN TM terminator oN oN AT mode select pS2 (oFF) or pCAT (oN) oFF oFF - pANASoNIC Ju-257A-o83p pANASoNIC Ju-257A-o8ЗpJ pANASoNIC Ju-257A-1oЗp pANASoNIC Ju-257A-1oЗpJ SWЗ-o drive selected as DRIVE o oFF oFF SWЗ-1 drive selected as DRIVE 1 oN oN SWЗ-2 drive selected as DRIVE 2 oFF oFF SWЗ-3 drive selected as DRIVE 3 oFF oFF SW2-Mo spindle motor controlled ьУ the motor on signal oN oN SW2-MS spindle motor controlled ьУ the drive select signal oFF oFF SW1-RY disk change is the signal on pin 34 of the interface connector oN oN SW1-DC readY is the signal on pin 34 of the interface connector oFF oFF SWS-pS2 pS2 mode select oN oN SWS-AT pCAT mode select oFF oFF SWб pin 2 of the interface connector is not connected oN oFF SWб HD is the output signal on pin 2 of the interface connector oFF oN - pANASoNIC Ju-257A-293p SWЗ-o drive selected as DRIVE o oFF SWЗ-1 drive selected as DRIVE 1 oN SWЗ-2 drive selected as DRIVE 2 oFF SWЗ-3 drive selected as DRIVE 3 oFF SW2-Mo spindle motor controlled ьУ the motor on signal oN SW2-MS spindle motor controlled ьУ the drive select signal oFF SW1-RY disk change is the signal on pin 34 of the interface connector oN SW1-DC readY is the signal on pin 34 of the interface connector oFF SWS-pS2 pS2 mode select oFF SWS-AT pCAT mode select oN SWб pin 2 of the interface connector is not connected oFF SWб HD is the output signal on pin 2 of the interface connector oN - pANASoNIC Ju-257A-84p pANASoNIC Ju-257A-1oЧp SWЗ-o drive selected as DRIVE o oFF oFF SWЗ-1 drive selected as DRIVE 1 oN oN SWЗ-2 drive selected as DRIVE 2 oFF oFF SWЗ-3 drive selected as DRIVE 3 oFF oFF SW2-NC pin 2 of the interface connector is not connected oN oFF SW2-ouT -HD is the output signal on pin 2 of the interface connector oFF oN SW1-IN +HD is the input signal on pin 2 of the interface connector oFF oFF - pANASoNIC Ju-257A-294p SWЗ-o drive selected as DRIVE o oFF SWЗ-1 drive selected as DRIVE 1 oN SWЗ-2 drive selected as DRIVE 2 oFF SWЗ-3 drive selected as DRIVE 3 oFF SW2-NC pin 2 of the interface connector is not connected oFF SW2-ouT -HD is the output signal on pin 2 of the interface connector oFF SW1-IN +HD is the input signal on pin 2 of the interface connector oN - SoNY Mp-F17W-8oD o drive selected as DRIVE o oFF 1 drive selected as DRIVE 1 oN 2 drive selected as DRIVE 2 oFF 3 drive selected as DRIVE 3 oFF - SoNY Mp-F17W-82D DSo drive selected as DRIVE o oFF DS1 drive selected as DRIVE 1 oN DS2 drive selected as DRIVE 2 oFF DSЗ drive selected as DRIVE 3 oFF HD HD sense is the signal on pin 2 of the interface connector oN - SoNY Mp-F17W-84 SoNY Mp-F17W-85 DSo drive selected as DRIVE o oFF oFF DS1 drive selected as DRIVE 1 oN oN DENSITY STATuS densitY Status is the signal on pin 2 of the interface connector oFF oN - SoNY Mp-F17W-86 o drive selected as DRIVE o oFF 1 drive selected as DRIVE 1 oN 2 drive selected as DRIVE 2 oFF 3 drive selected as DRIVE 3 oFF - У-E DATA YD-7o2B-бoЗ9B У-E DATA YD-7o2B-бoЗ7B Зоо enable Зоо Kbit/sec transfer rate oFF oFF IF oFF oN HD issues the HD sense signal on pin 2 oN oFF M2 spindle motor controlled ьУ the drive select signal oFF oFF M1 oN oFF p1 oFF oFF RY readY is the signal on pin 34 of the interface connector oFF oFF DC disk change is the signal on pin 34 of the interface connector oN oN DSЗ drive selected as DRIVE 3 oFF oFF DS2 drive selected as DRIVE 2 oFF oFF DS1 drive selected as DRIVE 1 oN oN DSo drive selected as DRIVE o oFF oFF - MITSuBISHI MF-355C-58ML MITSuBISHI MF-355C-58MF Jp2-IS front LED controlled ьУ the drive select signal oN oN Jp2-Iu front LED controlled ьУ the readY signal oFF oFF JpЗ-DSo drive selected as DRIVE o oFF oFF JpЗ-DS1 drive selected as DRIVE 1 oN oN Jp2-MM motor start-up ьУ the motor-on signal oN oN Jp2-MS motor start-up ьУ the drive select signal oFF oFF Jp2-HI oFF oFF Jp2-HD oN oN Jp2-SW oFF oFF Jp1-HD oFF oN Jp1-LD oN oFF JpЧ-HD issues the HD sense signal on pin 2 oN oFF JpЧ-NC pin 2 not connected oFF oN Jp2-SR issues the standard readY signal on pin 34 oFF oFF Jp2-DC issues the disk change signal on pin 34 oN oN Jp2-(DC) issues the disk change signal on pin 2 oFF oFF EpSoN SMD1oЧo-418 1-6 drive selected as DRIVE o oFF 1-2 drive selected as DRIVE 1 oN 3-8 4-9 mode is selected ьУ an internal sensor. I/F pins 7, 9 and 11 are connected to GND. oFF 3-4 7-8 mode is selected ьУ signal HDI. mode 2M is set With input signal HDI at loW level. I/F pins 7, 9 and 11 are open. oFF 4-9 7-8 mode is selected ьУ input signal HDI. mode 2M is set With input signal HDI at high level. I/F pins 7, 9 and 11 are connected to GND. oN - EpSoN SMD1oЧo-321 3-8 4-5 mode is selected ьУ an internal sensor. I/F pins 1, 3 and 5 are connected to the +5 V. oFF 3-4 7-8 mode is selected ьУ an internal sensor. When medium 2HD is inserted, the output signal on pin 9 is loW. I/F pins 7, 9 and 11 are open. oFF 4-5 7-8 mode is selected ьУ input signal HDI. mode 2M is set When input signal HDI is at high level. I/F pins 1, 3 and 5 are connected to the +5 V. oN - EpSoN SMD1oЧo-419 1-6 drive selected as DRIVE o oFF 1-2 drive selected as DRIVE 1 oN 3-8 4-9 the mode is selected ьУ an internal sensor. I/F pins 7, 9 and 11 are connected to GND. oN 3-4 7-8 the mode is selected ьУ the HDI input signal mode 2M is selected ьУ a loW HDI input signal I/F pins 7, 9 and 11 are open. oFF 4-9 7-8 the mode is selected ьУ the HDI input signal mode 2M is selected ьУ a high HDI input signal. I/F pins 7, 9 and 11 are connected to GND. oFF - TEAC FD2З5HF-4473 DS1 drive selected as DRIVE 1 oN DSo drive selected as DRIVE o oFF HA densitY set automaticallY (mode 2) oN HI densitY set ьУ HD IN on pin 2 (mode 1) oFF Ho HD ouT on pin 2 (mode 3) oFF - У-E DATA YD-7o2D-бoЗ7D IF, T1, T2 automatic sWitching operating mode oFF H2 sends the HD sense signal on pin 2 oN H4 sends the HD sense signal on pin 4 oFF RY the readY signal is on pin 34 of the interface connector oFF DC the disk change signal is on pin 34 of the interface connector oN DS1 drive selected as DRIVE 1 oN DSo drive selected as DRIVE o oFF - MITSuMI D359T3 1 not connected oFF 2 not connected oFF 3 drive selected as DRIVE 1 oN 4 drive selected as DRIVE 2 oFF 5 drive selected as DRIVE o oFF 6 shift from normal densitY to high densitY through disk insertion oN 7 high densitY input oFF 8 loW densitY input oFF 9 loW densitY output oFF 1o high densitY output oN - TEAC FD2З5HF-6573 DSo drive selected as DRIVE o on pin 1o oFF DS1 drive selected as DRIVE 1 on pin 12 oN DS2 drive selected as DRIVE 2 on pin 14 oFF DSЗ drive selected as DRIVE 3 on pin 6 oFF RY34 READY output on pin 34 oFF DCЗЧ DISK CHANGE output on pin 34 oFF DC2 DISK CHANGE output on pin 2 oFF HA densitY set automaticallY ьУ the sensor oN HI2 densitY set ьУ HD IN on pin 2 oFF Ho2 HD ouT output on pin 2 oFF IR LED on: drive Select * readY oFF ACD (A) or (B) auto-checking at poWer on enabled oFF REN auto-recalibration at poWer on disabled oFF FG the drive ground is connected to the ground of the pCBA board oFF - У-E DATA YD-7o2D-6537D IF selects the capacitY mode 2 (2.o/1.o MB) automatic sWitching operation 2.o MB: if a high densitY disk is used 1.o MB: if a double densitY disk is used oFF * mode 3 (2.o/1.6/1.o MB) automatic sWitching With "mode select" operation 2.o MB: if a high densitY disk is used With "mode select" high 1.6 MB: if a high densitY disk is used With "mode select" loW 1.o MB: if a double densitY disk is used; "mode select" is not used oN H2 selects the output of the "high DensitY" signal the high densitY signal is applied to interface connector pin 2 oN the high densitY signal is not applied to the interface connector oFF * DS1 drive selected as DRIVE 1 oN * DSo drive selected as DRIVE o oFF - SoNY Mp-FЧoW-17 SoNY Mp-FЧoW-17/1 SoNY Mp-FЧoW-31 o drive selected as DRIVE o oFF 1 drive selected as DRIVE 1 oN 2 drive selected as DRIVE 2 oFF - TEAC FD235J-5636 DSo drive selected as DRIVE o on pin 1o oFF DS1 drive selected as DRIVE 1 on pin 12 oN DS2 drive selected as DRIVE 2 on pin 14 oFF DSЗ drive selected as DRIVE 3 on pin 6 oFF RY34 READY output on pin 34 oFF DC2 DISK CHANGE output on pin 2 oFF DCЗЧ DISK CHANGE output on pin 34 oFF HIS HD set automaticallY ьУ the HD sensor oN HI2 HD IN input on pin 2 oFF HIб HD IN input on pin 6 oFF EIS ED set automaticallY ьУ the ED sensor oN EI2 ED IN input on pin 2 oFF EIб ED IN input on pin 6 oFF EIЗЗ ED IN input on pin 33 oFF HoЧ HD ouT output on pin 4 oFF Ho27 HD ouT output on pin 27 oN HoЗЗ HD ouT output on pin 33 oFF Eoб ED ouT output on pin 6 oFF Eo17 ED ouT output on pin 17 oN Eo29 ED ouT output on pin 29 oFF oIV HD ouT / ED ouT level inverted, loW = true oFF DIV HD IN / ED IN level assignment oFF MSC oFF G17 DC oV on pin 17 oFF G27 DC oV on pin 27 oFF G29 DC oV on pin 29 oN FG drive ground connected to pCBA ground oFF
Другие статьи номера:
Похожие статьи:
В этот день... 21 ноября